Quick Connect Couplings

Quick Connect Couplings - AVDV

Type AVDV : Double valve series couplings, both halves female threaded having valves which operate on the opposed poppet valve principle, valve consists of a spring loaded seat seal with attached valve. A quick pull on the sleeve and the assembly is disconnected, pull again, push the adaptor in coupler half and the unit is connected.

PRODUCT DESCRIPTION

PRECAUTION: Can not be connected / disconnected under pressure.

ADAPTOR < + > COUPLER
Size Thrds AL A B A. A/F. Coupled Length CL A SO S.L C.A/F Wrk. Prss. PSI
1/8" 32 20 12 14.Hex 70 52 13 24 19 18ø-14.A/F 4000
1/4" 38 25 13 17.Hex 77 60 14 30 20 23ø-19.A/F 4000
3/8" 40 27 13 22.Hex 80 66 16 38 24 28ø-24.A/F 3500
1/2" 45 30 15 28.Hex 90 74 18 44 27 35ø-30.A/F 3500
3/4" 55 35 20 35.Hex 110 88 23 54 30 40ø-35.A/F 3000
1" 60 37 23 41.Hex 120 95 25 62 32 48ø-41.A/F 3000
1¼" 68 42 26 60ø-54.A/F 135 110 28 75 36 60ø-54.A/F 2000
1½" 75 46 29 65ø-60.A/F 150 120 30 87 40 70ø-63.A/F 1500
2" 80 51 29 75ø-70.A/F 160 130 32 100 44 80ø-72.A/F 1000
2½" 90 56 34 88ø-82.A/F 180 145 38 110 45 92ø-85.A/F 500
3" 100 57 43 105ø-97.A/F 200 157 40 125 51 110ø-103.A/F 500

PROPERTIES & PHYSICAL FEATURES

These couplings are manufactured in various metals, with different end connections like, Female / Male Threaded, Hose Shank, Flange End, Socket / Butt Weld End.

METALS OF ASSEMBLY

BODY BALLS SPRINGS VALVES
Brass SS.304 SS.304 Brass
SS.304 SS.304 SS.304 SS.304
SS.316 SS.316 SS.316 SS.316
Carbon Steel Carbon Steel SS. Carbon Steel

SEAL MATERIAL

Selecting the right seal material depends on which fluid type and temperature range is used listed below. This will greatly influence the life of the couplings. The standard seal material is nitrile rubber.

RUBBER OPERATING TEMPERATURE RECOMMENDED APPLICATION
NITRILE -20°C TO + 90°C OIL RESISTANT
NEOPRENE -20°C TO + 100°C FREON / OZONE RESISTANT
EPDM -20°C TO + 120°C STEAM RESISTANT
SILICON -20°C TO + 180°C DRY HEAT
VITON -20°C TO + 220°C HEAT AND / OR CHEMICAL
TEFLON -40°C TO + 260°C HIGH TEMPERATURE

METALS OF ASSEMBLY

BODY BALLS SPRINGS VALVES
Brass SS.304 SS.304 Brass
SS.304 SS.304 SS.304 SS.304
SS.316 SS.316 SS.316 SS.316
Carbon Steel Carbon Steel SS. Carbon Steel

SEAL MATERIAL

Selecting the right seal material depends on which fluid type and temperature range is used listed below. This will greatly influence the life of the couplings. The standard seal material is nitrile rubber.

RUBBER OPERATING TEMPERATURE RECOMMENDED APPLICATION
NITRILE -20°C TO + 90°C OIL RESISTANT
NEOPRENE -20°C TO + 100°C FREON / OZONE RESISTANT
EPDM -20°C TO + 120°C STEAM RESISTANT
SILICON -20°C TO + 180°C DRY HEAT
VITON -20°C TO + 220°C HEAT AND / OR CHEMICAL
TEFLON -40°C TO + 260°C HIGH TEMPERATURE

QUALITY CONTORL

Each AVLOK Coupling manufactured goes through stringent quality control, right from the procurement of raw material upto final stage.

PRECAUTION :

  • Avoid connecting or disconnecting a coupling under pressure.
  • Residual pressure in a coupling may make it difficult to connect. In such a case, do not strike the valve end to depressurize it.
  • Improper selection of seal rubber may cause leakage.
  • Dust or flaws in the seal may cause leakage.
  • Improper selection or improper use of the products can cause personal injury and property damage.

All Dimensions are for reference only, and are subject to change without prior notice. Sizes and types other than featured above are available on request.